First, let’s keep it straightforward: the
Chery FX Front Left Wheel Fender Frame 602000268AA isn’t just a “flat metal piece”—it’s the “backbone support” for your FX’s front left wheel fender. Think of it as the sturdy skeleton that holds the fender in place, connects it to the car’s main body, and shields the engine bay from road mess. Without it, the fender would hang loose, rattle nonstop on bumps, or even fly off at high speeds—and dirt, water, or rocks from the wheel would splash
right into your engine’s parts.
This frame is
only for Chery FX models—always double-check your car’s VIN or owner’s manual to confirm! It’s built to match the FX’s front-end shape perfectly: the mounting holes line up with both the fender and the car’s front chassis, the edges fit snuggly against the bumper and
headlight (no weird gaps), and it’s shaped to hug the left wheel well (so it doesn’t rub against the tire). Grab a generic frame? You’ll run into headaches: it’s too big/small (won’t attach), bends easily (from a light curb tap), or leaves gaps (letting mud into the engine bay). Total hassle for a part that keeps your front end intact.
Don’t write it off as “just a support”—it does 4 key jobs to protect your car:
Holds the fender tight: It locks the front left fender to the chassis, so the fender doesn’t shift or wobble when you hit potholes or gravel roads. No frame = loose fender = annoying rattles (and potential damage).
Shields the engine bay: It acts as a barrier between the left wheel and the engine. When you drive through rain or mud, the frame blocks splashes from reaching hoses, wires, or the radiator—saving you from rust or short circuits.
Maintains body shape: It keeps the fender aligned with the bumper and headlight. A misaligned fender doesn’t just look ugly—it can catch wind (hurting fuel economy) or even scratch the headlight when you turn.
Absorbs small impacts: If you nudge a curb or a shopping cart with the left front, the frame soaks up some of the force. This stops the fender from cracking or the chassis from bending—cheaper to replace a frame than a whole chassis!
![602000268AA]( "602000268AA")
This 602000268AA frame is exclusive to Chery FX models—using the wrong one wastes money and risks damage:
Fits These Models: Chery FX (all trims; confirm via VIN to match your front-end design—some FX variants have minor chassis tweaks).
Won’t Fit These:
Other Chery models (e.g., Tiggo 7, Arrizo 6): Their front chassis and fender sizes are different—this frame won’t align with the bumper or wheel well.
Non-Chery vehicles (e.g., Geely Emgrand): Even if it “looks similar,” the mounting holes and shape are off—you’ll have to cut the frame (ruining it) to make it fit.
Fender Compatibility: Works with Chery FX’s original front left fender (both painted and unpainted). Aftermarket fenders may have different mounting points—stick to the original fender for a perfect match.
Installing this frame isn’t a DIY job—you need a mechanic or body shop that knows Chery FXs. Here’s why:
Perfect Alignment: Pros use tools to line the frame up with the fender, bumper, and headlight. Bad alignment = gaps, rattles, or even tire rub.
Proper Bolting: They tighten bolts to Chery’s exact specs (too loose = frame shifts; too tight = bolts snap).
Sealing Gaps: After installation, they add a small rubber seal between the frame and fender—stopping dirt from getting in.
Check for rust every 3 months: Look under the car at the frame—if you see orange spots, clean them with a rust remover and touch up the coating. Road salt in winter is a big rust risk!
Tighten bolts yearly: Have a mechanic check if the frame’s bolts are loose (vibration from driving can loosen them over time). Loose bolts = frame wobble.
Clean after mud/rain: Rinse the bottom of the front left wheel well with water—this washes off mud that can sit on the frame and cause rust.
![602000268AA]( "602000268AA")
Exclusive to Chery FX models (confirm via VIN), the 602000268AA frame supports the front left fender, holds it tight to the chassis, shields the engine bay from mud/water, keeps the fender aligned with the bumper/headlight, and soaks up small impacts (e.g., curb taps).
Made of rust-resistant high-strength steel with precision mounting holes, it fits the FX’s original fender perfectly—no gaps or misalignment. It won’t fit other Chery models (e.g.,
Tiggo 7) or non-Chery cars. Professional installation is needed; maintain by checking rust and bolt tightness. The original frame avoids aftermarket issues (bending, rust) and saves costly repairs.
Contact us
![602000268AA]( "602000268AA")
